[. . . ] 20G Silicone Input Wire Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 AWG Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . / 13. 5 grams Size. . . . . . . . . . . 1. 18" x 1. 04" x 0. 45" / 30. 0 x 26. 5 x 11. 5 mm LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 on-board SPECIFICATIONS Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Cut the wires to proper length and strip 3/16"­1/4" of insulation off the ends and tin with solder. 2. POWER DOWN SMART BOOST When finished running the vehicle, simply turn OFF the Smart Boost's switch. The Smart Boost's red and black 20G-silicone power wires connect to the ESC's battery power wires (where the ESC's main-battery wires connect to the ESC's PCB). Cut the wires to proper length and strip 3/16"­1/4" of insulation off the ends and tin with solder. 3. POWER DOWN SMART BOOST When finished running the vehicle, simply turn OFF the Smart Boost's switch. A. In a nitro vehicle, cut the input wires to proper length to reach the receiver battery pack, and strip and tin as instructed in Step 2. LOW BATTERY WARNING When the Smart Boost "blips" the vehicle's ESC throttle and servo power, it is advised to immediately cease running the vehicle and recharge the battery. A. In a nitro vehicle, cut the input wires to proper length to reach the receiver battery pack, and strip and tin as instructed in Step 2. LOW BATTERY WARNING When the Smart Boost "blips" the vehicle's ESC throttle and servo power, it is advised to immediately cease running the vehicle and recharge the battery. 3. In a nitro vehicle, connect the Smart Boost's red and black power wires to the corresponding red and black wires of a matching connector on the receiver pack (red to red & black to black). This allows you to plug the Smart Boost into your receiver battery pack. Solder the stripped and tinned ends of the Smart Boost's power wires to the ESC's main battery pack input or solder tabs. 3. 17032 Armstrong Avenue Irvine, CA 92614 (949) 833-8873 · FAX (949) 833-1631 Customer Service e-mail: cs@teamnovak. com Monday-Friday: 8:00am-5:00pm (PST) A. In a nitro vehicle, connect the Smart Boost's red and black power wires to the corresponding red and black wires of a matching connector on the receiver pack (red to red & black to black). This allows you to plug the Smart Boost into your receiver battery pack. Solder the stripped and tinned ends of the Smart Boost's power wires to the ESC's main battery pack input or solder tabs. Novak Electronics, Inc. 17032 Armstrong Avenue Irvine, CA 92614 (949) 833-8873 · FAX (949) 833-1631 Customer Service e-mail: cs@teamnovak. com Monday-Friday: 8:00am-5:00pm (PST) 4. [. . . ] Because Novak has no control over the connection & use of the module, no liability may be assumed nor will be accepted for any damage resulting from the use of this product. Every Novak module is thoroughly tested before leaving our facility and is, therefore, considered operational. By the act of connecting/operating module, user accepts all resulting liability. [. . . ]